|
|
08-08-2013, 09:24 PM | #1 |
Join Date: Mar 2006
Location: Georgia
Posts: 43
|
150cc upgrade no machining
HI all,
This may sound dumb coming from me but I really have not been keeping up with the 150cc upgrades. So I am looking to add a big bore kit upgrade for my customers that does not need machining and was wondering if anybody could tell me what the largest size bore I can order is that does not require machining. I want something that my folks can just install and go without any extra work. thanks for the help, John
__________________
John Dikov Valley Scooters www.scootersus.com www.valleyscooterparts.com www.valleyscootersdealers.com 203-500-0960 |
08-10-2013, 01:40 PM | #2 |
Join Date: Mar 2010
Location: Houston area
Posts: 945
|
I'd sure like to know that myself.
__________________
"Beer never broke my heart" - Luke Combs |
08-10-2013, 03:17 PM | #3 |
Most I know of is changing the jug to make it an actual 158cc. Then over stroke cranks.
__________________
2007 Sportiva Falcon GY6 150 4T 7,200+ Mi. 68 ( GPS Verified ) 76 MPG Few Mods, Lots-O-Tweaks 2003 Vento Zip R3i TurboCam 50cc 2T 8,500+ Mi. 62mph ( GPS Verified ) 90 MPG Seriously Modded Check out the new group for the Mountain Area! http://www.scootdawg.net/group.php?groupid=4 |
|
08-22-2013, 12:22 AM | #4 |
Join Date: Aug 2013
Location: sw fla
Posts: 7
|
you need a shorty exhaust,
__________________
Unauthorized advertising not allowed |
08-22-2013, 09:15 AM | #5 |
Only if you port the pass thoughs, in and out, and if it is an open exhaust.
__________________
2007 Sportiva Falcon GY6 150 4T 7,200+ Mi. 68 ( GPS Verified ) 76 MPG Few Mods, Lots-O-Tweaks 2003 Vento Zip R3i TurboCam 50cc 2T 8,500+ Mi. 62mph ( GPS Verified ) 90 MPG Seriously Modded Check out the new group for the Mountain Area! http://www.scootdawg.net/group.php?groupid=4 |
|
11-05-2013, 01:32 AM | #6 |
Join Date: Jan 2013
Location: midwest
Posts: 93
|
58.8mm is the largest size bore that can be installed on the GY6 engine without boring the case or a 58.5 but what is the point without a Stroker Crank. Just slapping in a 58.? is only going to give you about 5-6 more ccs around 156cc over 149.6 OEM. That will not even be noticeable to tell you the truth.
Lefty
__________________
Three Wheels keep me up You’ll never be old and wise if you weren’t young and crazy |
11-06-2013, 05:36 PM | #7 |
Join Date: Jan 2013
Location: midwest
Posts: 93
|
Here are my Mods:
Lefty Here is what my PST150H Ice Bear Trike currently has it was a 149.6cc Motor now it is 182cc motor: 62mm BBK 60mm Stroker Crank 16/37 Hoca Tranny Gears – Original were 13/40..I have 18/36 gears I have not put in yet Reduction gear is 43 teeth K&N Air Filter with a Short Stack SuperTrapp Muffler 1 1/4 Header Pipe 24mm Carb #122.5 Main Jet #38 Pilot Jet Peformance Coil/CDI Manual Choke Iridium Plug Prodigy Variator 12g Dr. Pulley Sliders 205/65-10 Kenda Load Tires-3"s taller than OEM 29 tooth Drive Sprocket-came with 24 tooth. DID 428 Pro V Series O-Ring Chain Givia 29" tall Windshield All Led bulbs Except the Headlights-I do not drive at night 4 way Flasher Turn Signal Beeper Relay for the Beeper connected to the Brakes VIP Trunk with Led lights Flasher on Vip Trunk lights Radio with SD card,MP3 connections
__________________
Three Wheels keep me up You’ll never be old and wise if you weren’t young and crazy |
02-12-2014, 01:15 AM | #8 |
Join Date: Feb 2014
Location: las vegas
Posts: 100
|
Yeah on a 150 its better to go with a stroker crank, you get more cc's without machining. with a +4 crank you will be at 160cc or with a +8 you could hit 170cc.
|
02-12-2014, 11:40 AM | #9 |
Banned
Join Date: Feb 2014
Location: MIAMI
Posts: 196
|
i would like to know this myself
|
02-13-2014, 11:06 AM | #10 |
Join Date: Mar 2011
Posts: 29
|
http://itistheride.boards.net/thread...-crank-project read this......
|
|
|