|
|
03-31-2013, 03:05 PM | #1 |
Join Date: May 2012
Posts: 37
|
adjustment screw
I sorta broke mine and Need a new one for my 150cc Znen interceptor...I found this at http://www.partsforscooters.com/Welc...+screw+and+nut but it says for 50ccs so I was wondering if anyone knew where I could find the right one please...thank you so much for anyones help!!!
|
03-31-2013, 09:56 PM | #2 |
Join Date: Jul 2008
Location: way up north in arkansas
Posts: 99
|
not interchangeable. May I ask how you broke yours? They usually do not break, and are you shure it is the screw and not what it screws into?
__________________
1983 Yamaha Riva 180cc 2007 Yamaha Majesty 400cc |
04-01-2013, 12:03 AM | #4 |
Join Date: Aug 2011
Location: Tierra Azul, NM
Posts: 739
|
I don't see just the screw but here is the whole assembly
http://www.partsforscooters.com/164-...ategory=133356 I assume its that screw and not another. Not sure how that would break...
__________________
Do not fear mistakes. You will know failure. Continue to reach out. - Benjamin Franklin Join the HARDCORE 1983 Honda GL650I SilverWing |
04-01-2013, 12:43 AM | #5 |
Join Date: May 2012
Posts: 37
|
yeah it looks exactly like the adjuster screws I have Thanks.. I cant beleive I broke it...I wasnt even going for like crazy tight or anything but I guess I broke it in half...I'm not so good at doing the valves anyways... I think I keep doing them to loose cause I can always here the ticking or tapping when I get the cover back on and start her up though...
|
04-01-2013, 12:49 AM | #6 |
Join Date: Aug 2011
Location: Tierra Azul, NM
Posts: 739
|
a little clicking is ok when the bike is cold. It should lessen as it warms
__________________
Do not fear mistakes. You will know failure. Continue to reach out. - Benjamin Franklin Join the HARDCORE 1983 Honda GL650I SilverWing |
04-01-2013, 11:35 AM | #7 |
Join Date: May 2012
Posts: 37
|
how much is to much then? lol it never did that before but then again i think the valves were fully closed before I started messing around in there... I just dont wanna break anything... I thought if there was clicking or tapping or w.e that they were to far open..
|
04-01-2013, 12:57 PM | #8 |
Join Date: Aug 2011
Location: Tierra Azul, NM
Posts: 739
|
The gap is there to allow for the expansion of the metal as it heats up. So the .004 gap should click initially. If it doesn't click you will have compression issues...
__________________
Do not fear mistakes. You will know failure. Continue to reach out. - Benjamin Franklin Join the HARDCORE 1983 Honda GL650I SilverWing |
04-01-2013, 01:26 PM | #9 |
Join Date: May 2012
Posts: 37
|
ahh ok so I shouldov prolly waited like 5 minutes to see how it was then?
|
04-01-2013, 01:34 PM | #10 |
Join Date: Aug 2011
Location: Tierra Azul, NM
Posts: 739
|
yes listen for tapping after it is fully warm it should not tap much once warm. Some people like them to just slightly click so they no they are certainly not tight
__________________
Do not fear mistakes. You will know failure. Continue to reach out. - Benjamin Franklin Join the HARDCORE 1983 Honda GL650I SilverWing |
04-01-2013, 10:13 PM | #11 |
Join Date: May 2012
Posts: 37
|
ohhhhhhhh ok thanks for clearing that up for me... now hopefully on wensday I can do it right lol..could I ask you if you had to get to the air/fuel mixture screw on the carb.. but it was covered how would you go about getting into that? thanks for all the help by the way! I dont know where Id be without scootdawg ^.^
|
04-01-2013, 10:45 PM | #12 |
Join Date: Aug 2011
Location: Tierra Azul, NM
Posts: 739
|
Some people drill the cap out sometimes they find a screw underneath sometimes its been altered to make it hard to adjust even uncapped. You may think about a new carb they are pretty cheap and might make life a lot easier...
__________________
Do not fear mistakes. You will know failure. Continue to reach out. - Benjamin Franklin Join the HARDCORE 1983 Honda GL650I SilverWing |
04-03-2013, 09:49 AM | #13 |
Join Date: May 2012
Posts: 37
|
ohhh I am sorta hoping for there to be a screw there cause I was reading on the old ScootDawg n someone else who had my scooter drilled theres out and was able to adjust it that way but Ill be finally attempting that and finnishing the valves today so wish me luck and thanks for the help once again :P
|
04-03-2013, 06:40 PM | #14 |
Join Date: May 2012
Posts: 37
|
well I tried and im not to sure but I made a video of her....its after a quick five minute ride after letting her warm up...she sounds louder now to but I can still hear it? Unless thats normal and im just going bonkers....well here it is (I hope i did this right)
|
04-03-2013, 06:55 PM | #15 |
Join Date: May 2011
Location: Nanty Glo, Pa.
Posts: 163
|
What did you set the valves at?
|
|
|