Register FAQ Community Calendar Today's Posts Search
Go Back   ScootDawg Forums > Media :: Reviews :: Classifieds :: General > General Scooter Discussion
Reply
 
Thread Tools Search this Thread Display Modes
Old 01-25-2016, 12:20 PM   #1
padly1995   padly1995 is offline
 
padly1995's Avatar
 
Join Date: Jul 2013
Posts: 87
gy6 50cc no power...

Hello, im repairing Jonway gy6 scooter for some guy.
First it was stuttering and i founded out that there was white plastic circle part that goes over the needle missing in the carburator.
I installed new one and scooter has stopped stuttering. But it still doesnt have any power. It goes around 20 - 30kph, it has realy bad acceleration and it goes on realy low rpm.
If I put scooter on the center stand, so wheel is up, it revs normaly, however if i press brake it instantly loses power.
I tried to play with air intake, but there is no difference. I checked valve cleareces and they are both OK. Also the camshaft is lined up as it should.
I can also hear some strange noise comming from under the flywheel I think.
What do you suggest me to do? Do you thing this could be CVT problem?
Thanks



Login or Register to Remove Ads
  Reply With Quote
Old 01-25-2016, 07:11 PM   #2
kz1000st   kz1000st is offline
 
kz1000st's Avatar
 
Join Date: Oct 2008
Location: Hyde Park, NY
Posts: 1,134
Here we go again. Check vacuum lines. A engine that pulls well without load but dies when loaded is having a mixture problem. A cracked intake manifold or a vacuum line might be the problem. Spray WD-40 around the intake area and see if the idle changes or picks up.
__________________
2008 Eagle Milano 150- 9,679 miles
2009 Honda Rebel 250- 10,434 miles
2009 CF Moto Fashion- 16,023 miles
2009 MC-114 50cc Cub Clone- 4,317 miles
twowheeler.yolasite.com/

That's 30,049 China Scootin miles and Counting.
  Reply With Quote
Old 01-26-2016, 11:36 AM   #3
padly1995   padly1995 is offline
 
padly1995's Avatar
 
Join Date: Jul 2013
Posts: 87
Quote:
Originally Posted by kz1000st View Post
Here we go again. Check vacuum lines. A engine that pulls well without load but dies when loaded is having a mixture problem. A cracked intake manifold or a vacuum line might be the problem. Spray WD-40 around the intake area and see if the idle changes or picks up.
Hello, thank you for anwser.
I thing that the manifold is good, because i changed it, but i will try with WD. I will also try to change vacuum lines. Thanks again



Login or Register to Remove Ads
  Reply With Quote
Old 01-27-2016, 11:01 AM   #4
padly1995   padly1995 is offline
 
padly1995's Avatar
 
Join Date: Jul 2013
Posts: 87
Quote:
Originally Posted by kz1000st View Post
Here we go again. Check vacuum lines. A engine that pulls well without load but dies when loaded is having a mixture problem. A cracked intake manifold or a vacuum line might be the problem. Spray WD-40 around the intake area and see if the idle changes or picks up.


Hello, i checked vacuum lines and intake manifold and everything seems to be OK. After that i dyscovered that there was 84 jet installed instead of 79. So I installed 79. Now scooter wants to die when i turn the throttle. Choke is working, i also put in new spark plug and its the same. Old spark plug was black.
I also uploaded a video:

Thanks.

UPDATE:
I founded out that the needle fall out of place, down on the jet. So i fixed that. It was a little bit better, but not much. Than i founded out that if i put electrical tape over inlet holls on airbox scooter goes almost good. Take off and mid-acceleration is good, but top end sucks. Something is wierd here haha. A replaced airbox, but nothing changed... Any suggestions? Thanks

Last edited by padly1995; 01-27-2016 at 06:23 PM.
  Reply With Quote
Old 01-27-2016, 08:00 PM   #5
bull   bull is offline
 
Join Date: Feb 2015
Posts: 257
check the compression and exhaust pipe gasket @ the head



Login or Register to Remove Ads
  Reply With Quote
Old 01-28-2016, 09:22 AM   #6
padly1995   padly1995 is offline
 
padly1995's Avatar
 
Join Date: Jul 2013
Posts: 87
Quote:
Originally Posted by bull View Post
check the compression and exhaust pipe gasket @ the head
I will and ill report later, thanks
  Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:20 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.