![]() |
|
![]() |
#16 |
![]() Join Date: Oct 2008
Location: Hyde Park, NY
Posts: 1,118
|
To me it's just an object lesson. One, if it looks too good to be true, it is. Two, people are such dopes sometimes. This is a dead simple, expensive two stroke that was trashed. So how do I believe that Chinese scooters are so bad when there are people who can blow up an expensive one?
I have a bunch of miles on mine without major headaches and no blown pistons. It just shows that it's the rider that makes the scooter. I bought it from a bad rider.
__________________
2008 Eagle Milano 150- 9,679 miles 2009 Honda Rebel 250- 10,434 miles 2009 CF Moto Fashion- 16,023 miles 2009 MC-114 50cc Cub Clone- 4,317 miles twowheeler.yolasite.com/ That's 30,049 China Scootin miles and Counting. |
![]() |
![]() |
#17 |
![]() Join Date: Feb 2012
Location: Las Vegas, Nv
Posts: 105
|
![]()
I mostly agree, though a really good deal pops up often enough that it feeds the dream. I've basically found that there are three types of vehicle owners. First, the one that keeps the paint bright and shiny, polishes up the chrome, keeps the upholstery clean and sparkly, and DOES NOTHING to keep the engine and drive in performance shape. Two, the opposite of that. The mechanic that spends all his energy and money on performance, keeping the engine tuned, the fluids changed, the tires properly inflated, and DOES NOT CARE if the body looks like crap. The third type, pretty much in the minority, has pride in the whole vehicle. It looks sharp, runs well, and rarely gets sold, since the owner did the research and bought what he wanted in the first place. So, absolutely, if it looks to good to be true, check it out with a wary eye. You will still get fooled some of the time, but there are deals to be made..
And I absolutely agree that it is the owner that is more often the cause of system failure that the vehicle manufacturer. It's been said that a craftsman is only as good as his tools. I strongly disagree. A skilled craftsman can use crappy tools if that is all that is available, and still get the job done. An uncaring poor craftsman can have the best tools money can buy, and still not get acceptable results. So, keep the cynicism, but know that there will be another deal, either next month or next year.. Shiny side up! |
![]() |
![]() |
#18 |
![]() Join Date: Feb 2015
Posts: 121
|
Wow, someone smoked the piston? Good grief. They must have been running it without oil or something.
![]() Once you remove the variator boss limiter and modify the ECU to disable the speed limiter, an otherwise stock Kymco 2-stroke can reach 45mph+. 30mph is the "as shipped" configuration, in which the variator boss prevents the variator from closing all the way (and reaching the highest ratio), and limits the engine at 6000RPM. There is no way to trash the engine in this configuration unless you run it without 2-stroke oil or screw around with the carburetor jetting / needle settings and make it run lean. The stock exhaust is also going to make your power start to drop off once you're at 8000 rpm. I weigh 260# and my Cobra Racer 2T will pull me up to 50mph (GPS verified) on a flat run, using a Technigas pipe, lighter roller weights, and carburetor adjustments so the engine doesn't burn up (the bike is otherwise stock). It can go a little faster downhill (55mph), but I'm nervous about that since its already at 9500rpm when I'm doing 50. I'm betting that the 72cc will allow you to get up to speed faster, but didn't add much to the top speed. Unfortunately my setup produces its best power at 8200+ RPM and runs pretty rich below that (needed due to how much air goes through when you reach resonation), making it "not the most fuel efficient 49cc scooter". 40mpg, lol. My Xciting 250CC (which is a heavier bike @ 400lbs, not that the Cobra is light @ 240 lbs) accelerates about the same for the first 40mph, but has a top end of 85ish MPH and gets better mileage to boot. I kind of needed that oomph, despite the fuel efficiency hit, because of how heavy I am (and my home town is somewhat hilly). For comparison, the YY250T doesn't want to get above 6500RPM @ 70mph on the highway (getting the same mileage as the XC250), and that's WoT, no oomph left. (I know its not rev limited since I can get it over 8000rpm on the center stand.) It's not a suitable vehicle for travelling on the highways in Connecticut (whereas the Xciting 250 is just barely suitable), since we have left-hand exits and people are usually doing 80 or more in that lane, making crossing over a risk I absolutely don't want to take on the YY250T. Last edited by Shadowfire; 01-31-2016 at 11:06 PM. |
![]() |
![]() |
|
|