150cc Cranking But No Start

heysus · 06-14-2016, 10:23 PM

I have a 2014 Tao Tao 150cc. I have a new battery, new starter, CDI is good, spark plug gets spark, I did a valve adjustment, gas is good, BUT it does not start.

I adjusted my valves to .004 inches. Bought a new CDI, but still the same result. The battery is a lithium Ion battery, and fully charged. New starter has not made a difference. Gas is the 91 kind.

When I put the spark plug on ground, it sparks. When I take the spark plug out of the engine, my engine cranks like it wants to start, but when the spark plug is inside, it cranks and then does a "currr" sound.

PLEASE HELP.

heysus · 06-14-2016, 10:24 PM

new air filter as well. the battery is also brand new. I got a new NGK spark plug and it is gapped at about .028-.032 inches.

coreyman · 06-15-2016, 07:20 AM

What about the carb? Have you cleaned it and/or done any adjustments?

heysus · 06-15-2016, 12:20 PM

I removed it and cleaned where the air comes in and out with rubbing alcohol. I've done no adjustments to it. The intake manifold is missing both screws holding it secure, so i think that may be the issue?

coreyman · 06-16-2016, 06:45 AM

Have you tried using starter fluid to get it going? After rebuilding my carb I had to prime it with starter fluid in the back of the carb where the air comes in.

blueboy5000 · 06-17-2016, 06:12 AM

Test compression with a compression testing gauge.

heysus · 06-19-2016, 12:51 AM

This is my current situation

I got it to start earlier with stater fluid, but then I tried again and am currently at this point.

Impaired · 06-20-2016, 09:27 PM

Quote:

Originally Posted by heysus

I removed it and cleaned where the air comes in and out with rubbing alcohol. I've done no adjustments to it. The intake manifold is missing both screws holding it secure, so i think that may be the issue?

So you're intake manifold isn't secure?
I assume that would create a pretty big vacuum leak which maybe why she isn't starting?

blueboy5000 · 06-21-2016, 08:01 AM

Quote:

Originally Posted by heysus

I removed it and cleaned where the air comes in and out with rubbing alcohol. I've done no adjustments to it. The intake manifold is missing both screws holding it secure, so i think that may be the issue?

You must have the intake securely fastened. A gy6 is so sensitive to intake vacuum, that even a slight crack in an intake manifold will cause a no-start condition.

heysus · 06-24-2016, 09:29 PM

Quote:

Originally Posted by Impaired

So you're intake manifold isn't secure?
I assume that would create a pretty big vacuum leak which maybe why she isn't starting?

I fixed the leak on the intake manifold, but it was the fuel/air ratio that was incorrect. It runs now! Thank you!

06-14-2016, 10:24 PM	#2
heysus Join Date: Jun 2016 Posts: 5	new air filter as well. the battery is also brand new. I got a new NGK spark plug and it is gapped at about .028-.032 inches. Last edited by heysus; 06-15-2016 at 01:26 AM.
	0

06-17-2016, 06:12 AM	#6
blueboy5000 Join Date: Jul 2011 Location: Connecticut Posts: 493	Test compression with a compression testing gauge. __________________ 2011 Roketa MC-23-150 4T 150cc 157 qmj 24mm carb w 115 main jet and paper cone air filter Manual petcock w Tygon fuel lines Scrappy Dog Scooters Retro-slash stainless straight-thru exhaust RED spring clutch Adjustable CDI (brand unknown, it's blue and red and works great!) KOSO high performance variator w 12g sliders Gates Powerlink 835-20-30 belt GPS verified 65mph on flats.
	0

06-15-2016, 12:20 PM	#4
heysus Join Date: Jun 2016 Posts: 5	I removed it and cleaned where the air comes in and out with rubbing alcohol. I've done no adjustments to it. The intake manifold is missing both screws holding it secure, so i think that may be the issue?
	0

06-19-2016, 12:51 AM	#7
heysus Join Date: Jun 2016 Posts: 5	This is my current situation I got it to start earlier with stater fluid, but then I tried again and am currently at this point.
	0